Steering wheel adapter + info vw 2009- ctuvw01 + dynaudio

DescriptionAutomakers have begun to present certain information on the screen of the factory device. By replacing the original equipment, you will not limit the previously available functions. The possibilities of presenting and controlling functions will certainly be appreciated by drivers. The interface is our first solution that allows the consumer to receive similar messages when controlling the heating or air conditioning, including when parking. Includes steering wheel remote control interface and vehicle display interface. Designed for all Alpine AV or AVN products with direct input for rear view camera. Product Features Display of climate control, parking sensor and heated seat information OEM navigation control function from factory steering wheel buttons Video input for rear view camera Universal connection cable for Alpine, Clarion, JVC, Kenwood, LG, Panasonic, Pioneer Sony, Zenec The Infodapter will retain several vehicle display functions after replacing the OEM radio or navigation system. Vehicle specific settings are available and will be displayed on an aftermarket head unit. The SWC buttons are required to access the Infodapter setup menu. Depending on the vehicle equipment and the range of functions and software of the retrofitted HU, individual operating functions may be omitted or replaced by other functions. Please refer to the installation recommendations of the individual components. Also check our listed OEM head units and compare the pictured wiring harness connectors with those in your vehicle and make sure that they fit optically and technically. Please note that in some cases not all functions are supported. For example Trailer Assist, E Call or other driver assistance and comfort systems. Before installation, check the vehicle menu for the various settings. Before final installation, also check the operation of the vehicle settings and system. Note: for vehicles with steering wheel controls, connector: 40 Pin Quadlock VW call up menu settings > purple-white return signal output connect to radio visualization of menu settings > RCA(m) yellow connect to the reversing camera input and configure vehicle settings and vehicle information > reflected on the rear camera input of the retrofit monitor vehicles with white OEM MFD instrument cluster vehicles with/without reinforced OEM system visualization OPS/climacontrol vehicles equipped with parking assistant front PDC > front PDC appears on the display after switching on the ignition exit the display > confirm using the vehicle PDC switch The +12V reversing signal is switched off from 3 km/h depending on the retrofit HU or installed camera, camera image or info adapter image unavailable: connecting additional GND signal to external RCA cable of camera and HUM connector Brand and model: Skoda Skoda Octavia (1Z) 01.2009 - 03.2013* Skoda Rapid (NH) 10.2012 - 04.2015 Skoda Roomster (5J) 06.2010 - 02.2015 Skoda Superb (3T) 07.2008 - 05.2013 Skoda Yeti (5L) 08.2009 - 10.2013 VW VW Caravelle (7H) 09.2009 - 05.2015** VW CC (3C/35) 02.2012 - 08.2016 VW Eos (1F) 10.2010 - 04.2015 VW Golf VI (1K) 11/2008 - 12/2012 VW Golf VI (1KM) 11/2009 - 04/2013 VW Golf VI (1K) 06/2011 - 07/2016 VW Golf VI Plus (1KP) 03/2009 - 01/2014 VW Multivan (7H) 09/2009 - 05/2015** VW Passat B7 (3C/362) 11/2010 - 10/2014 VW Polo V (6R) 06/2009 - 01/2014*** VW Scirocco III (13) 08/2008 - 04/2014 VW Sharan II (7N) 08/2010 - 04/2015 VW T5 Transporter (7H) 09/2009 - 05.2015** VW Tiguan I (5N) 06.2011 - 04.2016 VW Touran (1T) 08.2010 - 04.2015*vehicles with OEM HU receivers/stream**vehicles with reinforced OEM system > article VW T5/Touareg Quadlock MQS active system Adapter-housing: 13-1424-26***vehicles with reinforced Fender OEM systemThe following signals are available:Re-imported vehicles or vehicles with different software may not be compatible in terms of function. red: ignition terminal +12V 15 orange: lighting terminal +12V 58 violet/white: reverse gear signal +12 V green: parking brake signal GND load capacity of total outputs: 100 mA max. current demand greater than 100 mA: 1 relay coil resistance 75 Ohm min. 2 relays coil resistance 150 Ohm min.General installation instructions:Verification:1: Check all operational functions and vehicle settings functions OEM HU.2: Disconnect the voltage-free OEM HU.3: Check all interface connections for correctness in voltage-free mode.Connection and connection sequence:1: Check the settings and hardware configuration of the voltage-free interface.2: Check the configuration of the voltage-free radio connection cable.3: Connect the radio connection cable according to the retrofit HU instruction manual.4: Connect all other connections according to the retrofit HU instruction manual.5: Connect the entire installation to the main vehicle