Steering wheel adapter honda civic ufo (8th generation) hatchback 2005 - 2012. 7pin / 20pin climate control

Honda Civic UFO Steering Wheel AdapterThe product we offer is a Honda Civic UFO Steering Wheel Adapter (8th generation) Hatchback 2005 - 2012 CTSHO002. This accessory will allow you to safely install the radio and control it from the steering wheel. This is a convenient solution, and also increases the level of safety, because you do not have to take your hands off while driving. Another advantage of the adapter is that its installation will not affect the factory functions of the car, so driving comfort will not deteriorate in any way. Check compatibility with your carThe adapter is adapted for use in Honda Civic VII 2005 - 2012 cars. Only Hatchback models without factory navigation. Thanks to it, it is possible to connect audio equipment from most of the most popular companies in the car, also available in our online store. Note CAN bus Analog steering wheel remote control Connection: 17-pin / 20-pin Honda connector Connection: 5-pin / 10-pin display Blue: +12 V Amp Remote Check the DIP switch position Vehicles with air conditioning on the upper display Vehicles without navigation OEM with color monitor Vehicles without hybrid drive Supported time settings: Clock setup: Press Mode/SEL Reset simultaneously for 5 seconds Minutes / hours setup: Volume up / Volume down Time setup: Channel + / Channel - Exit setup: Press Mode/SEL Reset simultaneously for 5 seconds Supported OEM sound system Diagnostic LED: Solid blue > Interface active +12 V power supply, ignition current present Red > Steering wheel remote control button function detected Make and model: xa0 Honda Civic (FK1) 09/2005 - 12/2008 Honda Civic (FK1) 01/2009 - 12/2010 Honda Civic (FN2) 03/2007 - 12/2008 Honda Civic (FN2) 01/2009 - 12/2011The following signals are available:Re-imported vehicles or vehicles with different software may be functionally incompatible.Steering wheel remote controlClock settings supportedOEM sound system supportedGeneral installation instructions:Verification:1: Check all operational functions and vehicle adjustment functions of the OEM device.2: Disassemble the OEM device with the power off.3: Check the correctness and continuity of all interface connections with the power off.Connection and connection order:1: Adjust the interface settings and hardware configuration with the power off.2: Check the radio connecting cable configuration.3: Connect the radio connecting cable according to the operation manual of the retrofit device.4: Connect all other connections according to the retrofit device manual. 5: Connect the entire installation to the vehicle, making sure the power is turned on last. 6: Configure the interface software according to the instructions in the product description and user manual. 7: Configure the retrofit device according to the retrofit device manual for steering wheel remote control/camera/hands-free kit/antenna phantom power and other functions. 8: Test the steering wheel remote control and vehicle for proper operation. Interface hardware configuration changes and radio connection cable: 1: Changes with power off. Make the connection after the modification, see items 5 to 8 above.In the event of a failure of the interface or vehicle:1: Return to the OEM device2: Start the OEM device3: Establish a break in the CAN bus4: Check the hardware configuration of the interface5: Connection after a break in the CAN bus, see items 5 to 8 above.The connections, connection changes, alternative connections, connections of loose cables or extensions of connections of loose cables specified in the information text or the operating instructions are intended only for the information and guidance of trained personnel.Additional connections, changes in the wiring harness cable configuration or the use of alternative connections or extensions of connections:1: Connections and modifications may only be made by trained personnel.2: Connections and modifications must be checked against any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes. 3: Connections and modifications must be checked for functionality and accuracy by measuring and comparing them with the vehicle's wiring diagram. 4: Connections and modifications are made at your own risk and without guarantee of functionality. 5: Connections and modifications are made at your own risk and without guarantee of damage to the vehicle, retrofit device or interface. 6: Modifications to the pre-assembled wiring harness may void the product warranty.