Navilock NL-852ETTL GNSS receiver module with u-blox 8, 3.3 V TTL interface, PPS and antenna (62571)
Product reference: 11-4043619625710

Compact GNSS receiver module with an integrated patch antenna, backup battery and u-blox 8 chipset. Features a 6-pin WTB connector, 3.3 V TTL data interface and PPS output. The module requires a 5 V DC power supply.

Navilock NL-852ETTL GNSS receiver module with u-blox 8, 3.3 V TTL interface, PPS and antenna (62571)

Product reference: 11-4043619625710

Compact GNSS receiver module with an integrated patch antenna, backup battery and u-blox 8 chipset. Features a 6-pin WTB connector, 3.3 V TTL data interface and PPS output. The module requires a 5 V DC power supply.

You have 3 products in compare list, please remove someone and try again
  • Add to favorites products
  • Added to favorites products
  • Removed to favorites product
Add to compare
118,79 €
Product in warehouse

Guarantee
24 month

Delivery from Europe in
10 - 15
business days

Your message has been successfully sent!
Fill in the required fields*

Navilock NL-852ETTL – GNSS module for embedded positioning solutions

Navilock NL-852ETTL, manufacturer code 62571 and EAN 4043619625710, is an assembled satellite navigation receiver module with an antenna and backup battery. It is designed for integration into electronic devices that require positioning data.

Navilock NL-852ETTL – GNSS module for embedded positioning solutions

Multiple satellite systems and frequent data updates

The u-blox 8 UBX-M8030-KT chipset supports GPS, GLONASS, BeiDou, Galileo and QZSS signals and processes signals from up to 72 satellites simultaneously. Selectable GNSS configurations allow the receiver to be adapted to the application. Galileo support requires firmware version 3.01 or later.

Updates reach up to 18 Hz with a single GNSS system or up to 10 Hz with multiple systems, such as GPS and GLONASS. This is useful for recording a moving device’s position more frequently. AssistNow assistance data can shorten initial positioning, while SBAS corrections help improve accuracy.

TTL communication and PPS synchronization

NMEA 0183 messages GGA, GSA, GSV, RMC and VTG provide navigation data to a host controller. The PPS signal on pin 6 supports time synchronization. A GPS status LED helps check operation.

The TTL signal level is 3.3 V, while the module requires a 5 V DC supply. Signal levels and pin assignments must be matched before connection; this TTL model is not intended for direct USB or RS-232 connection.

Technical specifications

ParameterValue
Connector 6-pin WTB, 1.0 mm pitch
Data rate Automatic detection, up to 115200 bps
Sensitivity Down to −167 dBm
Positioning accuracy 2.5 m CEP; 2.0 m CEP with SBAS
Startup Cold start: approximately 26 s; hot start: approximately 1 s
Power supply and current 5 V DC; up to 45 mA
Dimensions as specified Approximately 30 × 30 × 7.9 mm
Operating temperature With battery: −20 to +60 °C; without battery: −40 to +85 °C

Integration, package contents and limitations

A device with a compatible TTL input and technical integration knowledge are required. The TTL version operates independently of the operating system, but the receiving application must process its data. The package contains one GNSS module; a connection cable is not included.

Specified accuracy and startup figures depend on reception conditions. The antenna requires an unobstructed view of the sky. Protect the module from water and condensation, and do not exceed +60 °C with the battery installed. PPS output sink current must remain below 100 mA.

Offensive and promotional comments are unpublished.
Testimonials not found!
Testimonial