Easily attach a compatible 4, 8, or 12-pin transducer to your boat's side with the mount, ensuring excellent sonar coverage at any speed.
Easily attach a compatible 12-pin scanning transducer to your boat's trolling motor with this bracket. The low-profile design provides excellent protection from underwater obstacles and easy installation.
Additional, external GPS antenna with SMA connector
Hard case with zipper for GPSMAP 62 64 63 66 navigators. Fits all Garmin GPSMAP 62 64 62st 64st 63 63sc 63st 66s 66st navigators. Internal dimensions 180x70 mm.
Garmin Nuvi, Drive 5 inch screen protector. Size 64x112mm
Garmin GPSMAP 66, 67 screen protector.
Garmin Nuvi, Drive 6 inch screen protector. Size 73x136mm
Add components to your NMEA 2000 network by connecting a T-connector to our trunk cable. The updated version of this T-connector differs from the previous one in that it has a 45-degree angle. Manufacturer code: 010-12935-10
Garmin NMEA 2000 trunk cable, length 2 meters. Garmin code: 010-12935-21
Hard case with zipper for Montana 700, GPSMAP-276Cx navigators. Internal dimensions 22 x 9 cm.
The RAM-B-202U consists of a B Size 2.54cm diameter rubber ball connected to a flat 6.35cm diameter plate. This mount has pre-drilled holes, including the universal AMPs hole pattern. Dydis B
The RAP-B-202U contains a 2.54cm diameter rubber ball connected to a flat 6.35cm diameter base. This mount has pre-drilled holes, including the universal AMPS hole pattern. Dydis B
The RAP-B-347U base consists of a 1" diameter rubber ball connected at right angles to a 2" x 1.7" square base. The base has four pre-drilled holes at each corner, making the universal 1.5 x 1.188 (hole spacing) AMPS hole pattern. Dydis B
The RAM-111BU consists of a C size 1.5" rubber ball connected at right angles to a flat 159 x 51mm rectangular plate. The plate contains different combinations of pre-drilled holes that will match many electronic devices and mounts, including marine GPS, CB radios, Ham radios, gimbal brackets,...
The RAM-B-101U consists of (2X RAM-B-202U + RAM-B*201U) a medium length B size double socket arm and two 64mm diameter round ball bases that contain the universal AMPS hole pattern. The ball and socket system provides shock and vibration damping, and allows for near-infinite adjustability to...
The RAM motorcycle handlebar base RAM-231-1U contains a 1.5" rubber ball designed to sit at right angles to the mounting rail. The rust proof metal u-bolt accommodates rails in 25-32mm diameter. The base also includes black cover caps to be placed over the exposed ends of the u-bolt. Dydis...
The RAM-B-101U consists of ( RAM-B-202U + RAM-B-201U + RAM-B-202U ) a double socket arm, 6.35cm diameter round base with the universal AMPS hole pattern and round adapter base that attaches directly to the bottom of the Garmin echo™ and Striker™ 4 Series. Designed into the mount is a 2.54cm...
RAP-403U The RAM Cable Manager creates an integrated route for electrical wiring and cleanly covers installation holes. A great addition to any surface mounting application. The RAM Cable Manager is made of glass filled nylon which has the benefit of creating a barrier between the RAM Surface...
The RAM-109V-3U consists of a 6" long single swing arm, 2.5" diameter round base with universal AMPs hole pattern and vertical surface mounting base. There are two (2) pivoting points on the mount: one at the swing arm and base and one at the center of the round base. Each pivoting point allows...
The RAM-109VSB consists of a short single ball joint, a rectangular vertical equipment mount. The lower circular base has pre-drilled holes, including a universal AMPS hole pattern. The rectangular equipment mount has various combinations of pre-drilled holes to accommodate most devices and...
RAM-109V-1U The RAM double swing arm mount includes two 6" long BENT swing arms mounted on a vertical surface mounting base. At the end of the device mount is a rectangular 6.25 x 2" top base. The pivoting points of the mount allow a complete 360 degree rotation.
RAM-109H-1U The RAM double swing arm mount includes two 6" long BENT swing arms mounted on a horizontal surface mounting base. At the device mounting end of the mount is a rectangular 6.25 x 2" top base. The pivoting points of the mount allow a complete 360 degree rotation.
The RAM-D-115-C consists of a base with a 5.71cm diameter D size ball, a short arm and a 15.87cm x 5.08cm marine electronic plate with a D size ball for supporting larger devices ( RAM-D-115BU + RAM-D-201U-C + RAM-D-202U ). This marine electronic plate contains different combinations of...