TomTom Aktiv-Magnethalterung 7 Zoll Gerte - USB-C
RAM mount for Garmin XT, Zumo, Montana, GPSMAP 276Cx series navigation receivers. The mount is designed for mounting on a motorcycle handlebar. An additional holder is required for the specific navigator model. Fits the following models: Montana XT, XT2, XT3 zūmo GPSMAP 276Cx (010-13879-04)...
Height-adjustable aluminium alloy tripod for positioning Deeper Range Extender equipment when fishing from the bank. Features a 51–136 cm height range, ball head, standard 1/4″-20 male thread and 8 kg load capacity. Measures 37 cm when folded and weighs 1.18 kg. A carry bag is included.
A backpack strap mount for compatible Garmin devices, featuring a nylon wrap and hook-and-loop fastening. Fits straps up to 9.5 cm wide and is MOLLE compatible. The safety tether adjusts from 5.1 to 61 cm.
Genuine Garmin backpack mount for a compatible handheld GPS device. Its nylon hook-and-loop harness wrap fits straps up to 3.75 inches wide and supports MOLLE attachment systems. An adjustable safety cord, approximately 2–14 inches long, keeps the device connected when detached from the mounting...
XGRIDS CZ02020001 is a GNSS RTK module for the LixelKity K1 scanner, enabling centimeter-level positioning under suitable conditions. It helps reference outdoor 3D scanning data to absolute coordinates. Used with LixelGO and a compatible RTK correction source.
The RAM-B-202U consists of a B Size 2.54cm diameter rubber ball connected to a flat 6.35cm diameter plate. This mount has pre-drilled holes, including the universal AMPs hole pattern. Dydis B
The RAP-B-202U contains a 2.54cm diameter rubber ball connected to a flat 6.35cm diameter base. This mount has pre-drilled holes, including the universal AMPS hole pattern. Dydis B
The RAP-B-347U base consists of a 1" diameter rubber ball connected at right angles to a 2" x 1.7" square base. The base has four pre-drilled holes at each corner, making the universal 1.5 x 1.188 (hole spacing) AMPS hole pattern. Dydis B
The RAM-111BU consists of a C size 1.5" rubber ball connected at right angles to a flat 159 x 51mm rectangular plate. The plate contains different combinations of pre-drilled holes that will match many electronic devices and mounts, including marine GPS, CB radios, Ham radios, gimbal brackets,...
The RAM-B-101U consists of (2X RAM-B-202U + RAM-B*201U) a medium length B size double socket arm and two 64mm diameter round ball bases that contain the universal AMPS hole pattern. The ball and socket system provides shock and vibration damping, and allows for near-infinite adjustability to...
The RAM motorcycle handlebar base RAM-231-1U contains a 1.5" rubber ball designed to sit at right angles to the mounting rail. The rust proof metal u-bolt accommodates rails in 25-32mm diameter. The base also includes black cover caps to be placed over the exposed ends of the u-bolt. Dydis...
The RAM-B-101U consists of ( RAM-B-202U + RAM-B-201U + RAM-B-202U ) a double socket arm, 6.35cm diameter round base with the universal AMPS hole pattern and round adapter base that attaches directly to the bottom of the Garmin echo™ and Striker™ 4 Series. Designed into the mount is a 2.54cm...
RAP-403U The RAM Cable Manager creates an integrated route for electrical wiring and cleanly covers installation holes. A great addition to any surface mounting application. The RAM Cable Manager is made of glass filled nylon which has the benefit of creating a barrier between the RAM Surface...
The RAM-109V-3U consists of a 6" long single swing arm, 2.5" diameter round base with universal AMPs hole pattern and vertical surface mounting base. There are two (2) pivoting points on the mount: one at the swing arm and base and one at the center of the round base. Each pivoting point allows...
The RAM-109VSB consists of a short single ball joint, a rectangular vertical equipment mount. The lower circular base has pre-drilled holes, including a universal AMPS hole pattern. The rectangular equipment mount has various combinations of pre-drilled holes to accommodate most devices and...
RAM-109V-1U The RAM double swing arm mount includes two 6" long BENT swing arms mounted on a vertical surface mounting base. At the end of the device mount is a rectangular 6.25 x 2" top base. The pivoting points of the mount allow a complete 360 degree rotation.
RAM-109H-1U The RAM double swing arm mount includes two 6" long BENT swing arms mounted on a horizontal surface mounting base. At the device mounting end of the mount is a rectangular 6.25 x 2" top base. The pivoting points of the mount allow a complete 360 degree rotation.
The RAM-D-115-C consists of a base with a 5.71cm diameter D size ball, a short arm and a 15.87cm x 5.08cm marine electronic plate with a D size ball for supporting larger devices ( RAM-D-115BU + RAM-D-201U-C + RAM-D-202U ). This marine electronic plate contains different combinations of...
The C-size RAM-111U-B consists of a 6.35cm diameter round base that contains the universal AMPs hole pattern, SHORT LENGTH double socket arm and 15.87cm x 5.08cm rectangle base ( RAM-111BU + RAM-201U-B + RAM-202U ). The rectangle base contains different combinations of pre-drilled holes which...
The RAM-109HU consists of a 152 mm long bent swing arm mounted on a horizontal surface base. At the device mounting end is a rectangular 158 x 51mm plate. There are two pivoting points on the mount: one at the base of the swing arm and one at the center of the rectangular plate. Each pivoting...
The RAM-202U consists of a 1.5" C size rubber ball connected to a 63mm diameter round plate. This mounting component includes pre-drilled holes using the universal AMPS hole pattern. Dydis C
RAM-109VU The RAM single swing arm mount consists of a 6" long swing arm mounted on a vertical surface mounting base. At the device mounting end of the mount is a rectangular 6.25" x 2" plate. There are two (2) pivoting points on the mount. One at the swing arm and base and one at the center of...