-
−2%
GNSS receiver with a built-in antenna, u-blox 8 chipset, MD6 connector and approximately 5 m cable. Supports GPS, GLONASS, BeiDou, Galileo and QZSS. A magnetic non-slip base and IPX6 protection simplify installation. The USB or serial cable for connection to a computer is sold separately.
GNSS receiver with a built-in antenna, u-blox 8 chipset, MD6 connector and approximately 5 m cable. Supports GPS, GLONASS, BeiDou, Galileo and QZSS. A magnetic non-slip base and IPX6 protection simplify installation. The USB or serial cable for connection to a computer is sold separately.
Guarantee
24 month
Delivery from Europe in
10 - 15
business days
The Navilock NL-8005P supplies positioning data to a computer running compatible navigation software. Manufacturer part number 62526 and EAN 4043619625260 identify this exact model. Its built-in antenna and long cable allow the receiver to be positioned where satellite reception is more favourable.


The u-blox 8 UBX-M8030-KT chipset supports GPS, GLONASS, BeiDou, Galileo and QZSS signals and can receive signals from up to 72 satellites simultaneously. The manufacturer specifies positioning accuracy of 2.5 m CEP, or 2 m CEP with SBAS. This is useful for navigation and position monitoring; the stated accuracy is not a guaranteed maximum error under all conditions.
AssistNow online and offline assistance and SBAS corrections are supported. A cold start takes approximately 26 seconds and a hot start approximately 1 second, allowing faster resumption when the necessary satellite data has been retained.
The receiver outputs NMEA 0183 messages GGA, GSA, GSV, RMC and VTG. This enables positioning and movement data to be used by software that understands these messages. The maximum update rate is 18 Hz with a single GNSS system or 10 Hz with multiple systems, such as GPS and GLONASS.
Pin 6 of the MD6 connector provides a PPS signal at an LVTTL 3.3 V logic level. This is intended for timing synchronisation with compatible hardware and is separate from the receiver's supply voltage.
The magnetic non-slip base helps secure the receiver to a suitable metal surface. The approximately 5 m cable provides flexibility when choosing its location, while an LED indicates GPS status. IPX6 protection suits environments exposed to powerful water jets, but does not establish suitability for immersion.
The receiver uses a Navilock MD6 connector with an RS-232 interface. A compatible MD6-to-USB or MD6 serial connection cable must be purchased separately. The receiver package alone is insufficient for direct connection to a standard computer USB port.
The manufacturer lists Windows Vista, Windows 7, Windows 8, Windows 8.1, Windows 10, Linux Kernel 2.6 and Mac OS X. Check the selected connection cable's drivers and navigation software compatibility before purchase. Appropriate software is required for navigation.
| Parameter | Value |
|---|---|
| Model / manufacturer part number | NL-8005P / 62526 |
| EAN | 4043619625260 |
| Processor / chipset | u-blox 8 UBX-M8030-KT |
| Connector | MD6, RS-232; PPS on pin 6, LVTTL 3.3 V |
| Signals | GPS L1, Galileo E1, QZSS L1: 1575.4200 MHz; BeiDou B1: 1561.0980 MHz; GLONASS L1 |
| Data rate | Automatic detection, up to 115200 bit/s |
| Update rate | Up to 18 Hz with single GNSS; up to 10 Hz with multiple GNSS |
| Sensitivity | Up to −167 dBm |
| Power supply / current | 5 V DC / maximum 45 mA |
| Protection / operating temperature | IPX6 / −20 to +60 °C |
| Length | Approximately 5 m |
| Dimensions as specified | Approximately 65 × 45 × 22 mm |
| Housing | Black, PC / ABS |
The USB or serial connection cable is sold separately. The unverified 0.250 kg weight from the previous description is not presented as a receiver specification.