Navilock NL-803P GNSS receiver, u-blox 8 EVA-M8Q, MD6, PPS, 5 m cable, IPX7 (62798)
Product reference: 11-4043619627981

Vehicle-mountable GNSS receiver with a built-in antenna, u-blox 8 EVA-M8Q chipset and a 5 m cable with an MD6 connector. Supports GPS, GLONASS, Galileo, BeiDou and QZSS signals, NMEA 0183 and a PPS output. Positioning accuracy is 2.5 m CEP or 2 m CEP with SBAS. A USB or serial connection cable is sold separately.

Navilock NL-803P GNSS receiver, u-blox 8 EVA-M8Q, MD6, PPS, 5 m cable, IPX7 (62798)

Product reference: 11-4043619627981

Vehicle-mountable GNSS receiver with a built-in antenna, u-blox 8 EVA-M8Q chipset and a 5 m cable with an MD6 connector. Supports GPS, GLONASS, Galileo, BeiDou and QZSS signals, NMEA 0183 and a PPS output. Positioning accuracy is 2.5 m CEP or 2 m CEP with SBAS. A USB or serial connection cable is sold separately.

You have 3 products in compare list, please remove someone and try again
  • Add to favorites products
  • Added to favorites products
  • Removed to favorites product
Add to compare
142,79 €
Product in warehouse

Guarantee
24 month

Delivery from Europe in
10 - 15
business days

Your message has been successfully sent!
Fill in the required fields*

Navilock NL-803P – GNSS receiver for vehicle navigation systems

The Navilock NL-803P combines a u-blox 8 EVA-M8Q chipset with a built-in antenna to provide satellite positioning data to a computer or another compatible system. Used with a laptop, a suitable connection cable and navigation software, it can form part of a navigation installation in a car, truck or bus. Manufacturer part number 62798 matches EAN 4043619627981.

Navilock NL-803P – GNSS receiver for vehicle navigation systems

Multiple satellite systems and frequent position updates

The receiver supports GPS, GLONASS, Galileo, BeiDou and QZSS signals and reception from up to 72 satellites simultaneously. Updates reach up to 18 Hz in single-GNSS mode and up to 10 Hz in multi-GNSS mode. Frequent updates are useful for applications that need to track changes in a moving vehicle's position.

The manufacturer specifies positioning accuracy of 2.5 m CEP, improving to 2 m CEP with SBAS. CEP is a statistical positioning accuracy measure rather than a guaranteed maximum error. AssistNow online and offline assistance and SBAS services are supported. A cold start takes approximately 26 seconds, while a hot start takes approximately 1 second.

MD6 connection, NMEA data and PPS output

The MD6 connector allows a separately sold USB or serial connection cable to be selected for the host equipment's interface. NMEA 0183 messages GGA, GSA, GSV, RMC and VTG provide navigation data to software that supports them. Automatic baud-rate detection supports speeds up to 115200 bps.

Pin 6 provides a PPS signal for timing synchronisation tasks in compatible equipment. Its electrical level is LVTTL 3.3 V, so the receiving equipment's requirements must be checked before connection.

Vehicle roof installation

The low-profile black housing is secured using the supplied stainless steel nut and washer. The approximately 5 m cable provides flexibility when routing the connection from the roof to the equipment installation point. An IPX7 protection rating and an operating temperature range of −10 to +50 °C allow outdoor use when the manufacturer's installation requirements are followed.

Technical specifications

ParameterValue
Manufacturer and model Navilock NL-803P
Manufacturer part number / EAN 62798 / 4043619627981
Processor / chipset u-blox 8 EVA-M8Q
Connector 1 × MD6 male
GPS, Galileo, QZSS frequency L1, E1, L1 respectively; 1575.4200 MHz
GLONASS frequency L1; 1602 + k × 0.5625 MHz
BeiDou frequency B1; 1561.0980 MHz
Assistance systems AssistNow; SBAS: WAAS, EGNOS, QZSS, MSAS
Sensitivity Down to −164 dBm
Power supply 5 V DC; current consumption up to 45 mA
Length Approximately 5 m
Dimensions as specified Approximately Ø 62 × 21 mm, excluding mounting thread
IP protection rating IPX7
Operating temperature −10 to +50 °C

System requirements and package contents

The manufacturer lists Android 10.0 or later, Chrome OS 90.0 or later, Linux Kernel 5.8 or later, and Windows 10 / 10-64 / 11. A suitable MD6 connection cable and application-appropriate software are required. This is an external receiver that requires a separate system for navigation.

  • MD6 serial GNSS receiver with an approximately 5 m cable.
  • Mounting hardware: stainless steel nut and washer.

A USB or serial connection cable is not included. The 5 m specification in the product name refers to cable length, not horizontal positioning error.

Offensive and promotional comments are unpublished.
Testimonials not found!
Testimonial