Ford sync 4 reversing camera adapter with 12-inch, 13.2-inch monitor.

The adapterxa0equips your car with a reversing camera and displays the image on the original car radio (which must be prepared for this). Some adapters are plug and play solutions, others require connecting cables or other modifications. Please read the installation instructions in advance or contact us if you have any questions.xa0In addition to the adapter, you will need a reversing camera. We encourage you to also check out our full range under thexa0reversing cameras tab.The video interface allows you to connect a reversing camera, a front camera with automatic mode and any two video sources (for side cameras or other retrofit devices such as USB players, DVB-T2 tuners, ...) to the vehicle manufacturer's factory infotainment system with the system. In addition, the video interface has an HDMI input that can be used to connect an HD reversing camera or another HDMI source (e.g. iOS/Android device, laptop, streaming device).All video inputs are compatible with CVBS and AHD. 1 x FBAS rear view camera video input 1 x FBAS front camera video input 2 x CVBS/AHD input for side cameras or other devices to upgrade (e.g. USB devices, DVB-T2 tuner, etc.) All inputs compatible with NTSC and PAL Supported AHD resolutions 720p NTSC (30 Hz), 720p PAL (25 Hz), 960p NTSC (30 Hz), 960p PAL (25 Hz), 1080p NTSC (30 Hz), 1080p PAL (25 Hz). 1 HDMI input for HD rear view camera or other HDMI source (e.g. iOS/Android device, laptop, streaming device, DVB-T2 tuner, etc.) Automatic switching to rear view camera input when reverse gear is engaged Automatic switching to front camera after reverse gear for 5, 10, 15 or 20 seconds Distance lines for rear view camera can be activated (not available for all vehicles) PDC graphics can be activated (not available for all vehicles) No image while driving (ONLY for powered video sources) Make and model: Ford Bronco from 06.2021 full version Sync4 with APIM and 12 or 13.2-inch tablet monitor Ford Focus from model year 2022 full version Sync4 with APIM and 12 or 13.2-inch tablet monitor Ford Tourneo Custom 2 from 07.2023 full version Sync4 with APIM and tablet monitor 12 or 13.2 inch Ford E-Transit from 11.2020 full version Sync4 with APIM module and 12 or 13.2 inch tablet monitor Ford Transit Custom 2 from 07.2023 full version Sync4 with APIM module and 12 or 13.2 inch tablet monitorLimitations CAN bus compatibility -xa0The compatibility of the interface with the CAN bus may be limited in its entirety to some vehicles or to individual functions. This can be noticeable both during installation and later. The interface with all video inputs can be operated via analog switching signals without having to connect to the vehicle's CAN bus. Individual additional functions have been omitted, see below. xa0 Video only -xa0The interface allows the connection of video only, to connect AUDIO you must use the factory AUX input or an external FM modulator.xa0If 2 AV sources are connected, the desired audio switching will require additional electronics. Factory Rear View Camera - Automatic switching to the rear view camera is only possible when reverse gear is engaged. To delay the return, an additional electronic part is required. Front Camera - The front camera will automatically switch to 5,10,15 or 20 seconds after reverse gear is disengaged. It is possible to manually switch the front camera using the external keyboard. Guide lines and PDC -xa0 If the vehicle's CAN bus is not fully compatible with the interface, the route line and optical PDC display functions cannot be used.Connectors Image input: 4+2 pin HSD Power supply and CAN bus: Plug Play (depending on the vehicle) Video inputs (2x): Cinch sockets Reversing camera input: RCA socket Front camera input: RCA socket Trigger cables (4x): Open cable ends Additional video input: HDMI HDMI audio output: 3.5 mm jack socket xa0Specifications Operating voltagexa0 xa0- 12 V DC (7 ~ 25 V) Standby currentxa0 -xa0 4mA Current consumptionxa0 -xa0 235mA Video inputxa0 -xa0 0.7 ~ 1 V. Video input formatsxa0 -xa0 PAL / NTSC Operating temperature xa0 xa0-40 ° C to + 85 ° C Video box dimensionsaxa0 -xa0 117 x 25 x 108 mm (W x H x D)Legal notice While driving, you must not distract the driver, directly or indirectly, with moving images. In most countries / states, this is prohibited by law. Apart from being used when stationary, this product is only intended to display standing menus (e.g. MP3 menus from DVD players) or rear view camera images while driving.