Adapter for steering wheel control for Porsche 911, Cayenne, Macan, Panamera, amplifier bridge.

When replacing the factory radio with an aftermarket radio, the original functions of the steering wheel remote control must be retained. Depending on the vehicle equipment and the range of functions and software of the retrofit device, individual operating functions may be omitted or replaced with other functions. Compare the adapter plugs shown with the plugs in your vehicle and make sure that they match visually and technically. Also check whether one of the listed original factory radios is installed in your vehicle. Before final installation, check the operation of the vehicle, vehicle and steering wheel remote control settings for operation. Note: CAN BUS Connection: Porsche 40-pin Quadlock connector Connection: OEM MOST sound system > Cinch(m) red/white Connection: OEM USB HSD LVDS > USB-A Connection: rear view camera OEM > Cinch(m) yellow Vehicles with OEM PCM 3.1 Vehicles with most OEM sound systems Vehicles without 360° camera system OEM Vehicles without Burmester 3D High End surround sound system OEM Vehicle settings not supported DIP switch settings for retrofit device manufacturer (see BDA) Cinch(m) > front preamplifier output for retrofit radio Fader function not supported Brand and model : Porsche 911 (991) 12/2011 - 01/2017 Porsche Cayenne (92A/958) 05/2010 - 12/2017 Porsche Macan (95B) 04/2014 - 08/2018 Porsche Panamera (970) 09/2009 - 07/2016 The following signals are provided: Re-imported vehicles or vehicles with different software may have incompatible features. red: ignition terminal +12V 15 orange: lighting terminal +12V 58 purple/white: reversing signal +12 V pink: speed signal green: handbrake signal ground GND Output load capacity: max. 250 mA. Current requirements greater than 250 mA: 1 relay coil resistance 75 ohms min. 2 Ralais coil resistance 150 Ohm min. Steering wheel remote control OEM sound system MORE> muffler function not supported General installation instructions: Testing: 1: Check all operating functions and vehicle setting functions of the OEM device 2: Disassemble the OEM device without voltage 3: Check all interface connections for correctness and continuity without voltage Connection and connection sequence:1: Make settings and hardware configuration of the voltage-free interface2: Check the configuration of the radio connection cable3: Connect the radio connection cable according to the instructions operating the retrofit device4: Make all other connections in accordance with the retrofit device's operating instructions5: Connect the entire installation to the vehicle with the live connection last6: Configure the interface software in accordance with the information contained in the text of the article and in BDA7: Configure the retrofit device in accordance with the retrofit device's operating instructions steering wheel remote control/camera/FSE/antenna phantom power and others8: Functional test of the steering wheel remote control and vehicleHardware configuration changes to the interface and radio connection cable:1: Make changes without voltage2: Connection after modification, see 5 to 8 aboveIf the interface or vehicle is malfunctioning:1: Upgrade to OEM device2: Operate OEM device3: Establish CAN bus silence4: Check interface hardware configuration5: Connection after resting the CAN bus, see 5 to 8 aboveConnections, connection changes, alternative connections, connections loose cables or connection extensions loose cable connections given in the information text or operating instructions are for orientation and information purposes only for trained specialist personnel. Additional connections, changes to the configuration of the wires in the cable harness or the use of alternative connections or connection extensions:1: Connections and changes may be made only trained specialists2: Before connection, check connections and changes for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes3: Before connection, check connections and changes for operation and correctness by measuring and comparing using the vehicle wiring diagram4: Connections and changes are made at your own risk and functionality is not guaranteed5: Connections and changes are made at your own risk, with no guarantee of damage to the vehicle, retrofitted device or interface6: Modifications to the pre-assembled wiring harness may void the product warranty