Adapter for steering wheel control for BMW series 1, 3, 5, x5, x6 amplifier bridge.

When replacing the factory radio with an aftermarket radio, the original functions of the steering wheel remote control must be retained. Depending on the vehicle equipment and the range of functions and software of the retrofit device, individual operating functions may be omitted or replaced with other functions. Compare the adapter plugs shown with the plugs in your vehicle and make sure that they match visually and technically. Also check whether one of the listed original factory radios is installed in your vehicle. Before final installation, check the operation of the vehicle, vehicle and steering wheel remote control settings for operation. Note: CAN Bus Connection: BMW 40-pin Quadlock connector Connection: +12 V continuous current, yellow battery terminal 30 with fuse Connection: OEM MOST sound system > Cinch(m) red/white Connection: Steering wheel remote > 3.5mm jack/loose cable Vehicles with OEM Business Professional Vehicles with OEM sound system MOST Vehicles without iDrive PDC supported* Warning sounds not supported* DIP switch settings for retrofit manufacturer (see BDA) Cinch(m) > front preamplifier output for retrofit radio Fader function not supported Brand and model: BMW 1 Series (E81) /82/87/88) 03/2004 - 10/2013 BMW 3 Series (E90/91/92/93) 03/2005 - 10/2013 BMW 5 Series (E60/61) 07/2003 - 07/2010 BMW X5 (E70) 03/2007 - 09/2013 BMW X6 (E71/E72) 05/2008 - 06/2014 The following are delivered signals: Re-imported vehicles or vehicles with different software may have incompatible functions. red: ignition terminal +12V 15 orange: lighting terminal +12V 58 purple/white: reversing signal +12 V pink: speed signal green: handbrake signal ground GND Output load capacity: max. 250 mA. Current requirements greater than 250 mA: 1 relay coil resistance 75 ohms min. 2 Ralais coil resistance 150 Ohm min. Steering wheel remote control OEM sound system > muffler function not supported *Vehicles with PDC/warning horns > Article: can-pdcGeneral installation instructions: Test:1: Check all operating functions and vehicle setting functions of the OEM device2: Disassemble the OEM device without voltage3: Check all interface connections for correctness and continuity without voltageConnection and order of connections:1: Make settings and hardware configuration of the interface without voltage2: Check the configuration radio connection cable3: Connect the radio connection cable in accordance with the operating instructions of the retrofitted device4: Make all other connections in accordance with the operating instructions of the retrofitted device5: Connect the entire installation to the vehicle with the live connection last6: Configure the interface software in accordance with the information contained in the text of the article and in BDA7: Configuration of the retrofitting device in accordance with the operating instructions of the retrofitting device remote control on steering wheel/camera/FSE/antenna phantom power and others 8: Functional test of the steering wheel remote control and vehicle Changes in the hardware configuration of the interface and radio connection cable: 1: Make changes without voltage 2: Connection after modification, see 5 to 8 above If the interface or vehicle is not working properly :1: Update to OEM device2: Support OEM device3: Establish CAN bus silence4: Check hardware configuration interface5: Connection after resting the CAN bus, see 5 to 8 aboveConnections, connection changes, alternative connections, loose cable connections or extensions of loose cable connections given in the information text or operating instructions are for orientation and information purposes only for trained specialist personnel. Additional connections, changes in the wiring configuration of the wiring harness or the use of alternative connections or connection extensions:1: Connections and changes must only be made by trained specialists2: Before connecting, check connections and changes for any manufacturer's approvals or manufacturer's warranty conditions that may be affected by changes3: Before connection, check connections and changes for functionality and correctness by measuring and comparing, using the vehicle wiring diagram4: Connections and changes are made at your own risk and functionality is not guaranteed5 : Connections and changes are made at your own risk, with no guarantee of damage to your vehicle, retrofit device or interface6: Modifications to the pre-assembled wiring harness may void your product warranty