Adapter for steering wheel control BMW series 1, 3, 5, x5, x6 amplifier bridge.

When replacing the factory radio with an aftermarket radio, the original functions of the steering wheel remote control must be retained. Depending on the vehicle's equipment and the scope of functions and software of the retrofit device, individual operating functions may be omitted or replaced by other functions. Compare the adapter plugs shown with those in your vehicle and ensure they match visually and technically. Also check whether one of the listed original factory radios is installed in your vehicle. Before final installation, check vehicle operation, vehicle settings and the steering wheel remote control for functionality. Note: CAN Bus Connection: 40-pin BMW Quadlock connector Connection: +12 V continuous current, yellow battery terminal 30 with fuse Connection: OEM MOST sound system > Cinch(m) red/white Connection: Steering wheel remote control > 3.5 mm socket / flying lead Vehicles with OEM Business Professional device Vehicles with OEM MOST sound system Vehicles without iDrive Supported PDC controller* Warning tones not supported* DIP switch settings for the manufacturer of the retrofit device (see BDA) Cinch(m) > front preamplifier output for retrofit radio Fader function not supportedBrand and model: BMW 1 series xa0 (E81/82/87/88) 03/2004 - 10/2013 BMW 3 series xa0 (E90/91/92/93) 03/2005 - 10/2013 BMW 5 series (E60/61) 07/2003 - 07/2010 BMW X5 (E70) 03/2007 - 09/2013 BMW X6 (E71/E72) 05/2008 - 06/2014The following signals are provided: Re-imported vehicles or vehicles with different software may have incompatible functions. red: ignition terminal +12V 15 orange: lighting terminal +12V 58 purple/white: reversing signal +12 V pink: speed signal green: handbrake signal ground GND Output load capacity: max. 250 mA. Current requirements greater than 250 mA: 1 relay coil resistance 75 Ohm min. 2 Ralais coil resistance 150 Ohm min. Steering wheel remote control OEM sound system > muffler function not supported *Vehicles with PDC / warning signals > Article: can-pdcGeneral installation instructions:Testing:1: Checking all operational functions and vehicle settings functions of the OEM device2: Dismantle the OEM device without voltage3: Check all interface connections for correctness and continuity without voltageConnection and connection sequence:1: Perform settings and hardware configuration of the interface without voltage2: Check the configuration of the radio connection cable3: Connect the radio connection cable according to the operating instructions of the retrofitted device4: Make all other connections according to the operating instructions of the retrofitted device5: Connect the entire installation to the vehicle with a live connection last6: Configure the interface software according to the information in the article text and in the BDA7: Configure the retrofitted device according to the operating instructions of the retrofitted device steering wheel remote control / camera / FSE / antenna phantom power and others8: Functional test of the steering wheel remote control and vehicleChanges to the hardware configuration of the interface and the connecting cable radio:1: Make changes without voltage2: Connection after modification, see 5 to 8 aboveIf the interface or vehicle is not functioning properly:1: Upgrade to an OEM device2: Operate the OEM device3: Establish CAN bus silence4: Check the hardware configuration of the interface5: Connection after CAN bus rest, see 5 to 8 aboveConnections, changes in connections, alternative connections, connections of loose cables or extensions of connections of loose cables given in the information text or the operating instructions are for orientation and information purposes only for trained specialist personnel.Additional connections, changes in the wiring configuration in the wiring harness or the use of alternative connections or extensions of connections:1: Connections and changes may only be carried out by trained specialists2: Before connecting, check the connections and changes for any manufacturer approvals or manufacturer warranty conditions that may be affected by the changes3: Before connecting, check the connections and changes for operation and correctness by measuring and comparing using the vehicle's wiring plan4: Connections and changes are carried out at your own risk and do not guarantee 5: Connections and changes are made at your own risk, with no guarantee of damage to the vehicle, retrofitted device or interface 6: Modifications to the pre-assembled wiring harness may void the product warranty