Adapter do sterowania z kierownicy Can Bus Fiat Ducato III 2015- CTSFA015.2

Retain the original functions of your steering wheel remote control when replacing your factory radio with an aftermarket one. Depending on the vehicle equipment and the scope of functions and software of the retrofitted HU, individual operating functions may be omitted or replaced by other functions. Compare the wiring harness connectors shown with the connectors in your car and make sure they match visually and technically. Check if one of the listed OEM head units was originally installed. Before final installation, also check vehicle functionality, vehicle settings and SWC functionality.

Comments:

• CAN Bus
• connector: 52 Pin Fiat
• vehicles with OEM HU
• vehicles without Continental VP1 / VP2 / Daiichi OEM HU*

Make and model:

• Fiat Ducato (250) 05/2014 - 11/2021

The following signals are available:

• Re-imported vehicles or vehicles with different software may not be feature compatible.
• red: ignition terminal +12V 15
• orange: lighting terminal +12V 58
• purple/white: reverse signal +12V
• pink: speed pulse signal
• green: parking brake signal GND
• total output load capacity: 100 mA max.
• current demand greater than 100 mA:
• 1 relay coil resistance 75 Ohm min.
• 2 relays coil resistance 150 Ohm min.

SWC

*vehicles with Continental VP1 / VP2 / Daiichi OEM HU: SWC Citroen/Fiat/Opel/Peugeot VP1/VP2/Daiichi 52Pin > article: 42sfa019

Note: SELECT THE CABLE FOR THE RADIO RECEIVER YOU WANT TO INSTALL (TO BE PURCHASED SEPARATELY)

• ALPINE
• BLAUPUNKT
• BLAUPUNKT NEW YORK / SONY
• CLARION
• JVC
• JVC KW-AVX
• KENWOOD
• NAKAMICHI / PHILIPS
• LG
• PANASONIC
• PANASONIC AV
• PIONEER
• PIONEER AV
• ZENEC
• UNIVERSAL FOR CHINESE RADIO RECEIVERS

Features and benefits

• Allows you to install an aftermarket OEM radio and retain the factory steering wheel controls
• Safety: Allows you to keep your hands on the wheel and focus on driving
• Plug and Play, no wire cutting required
• Retains original vehicle features such as date, time, and temperature display
• For interfaces where the phone buttons are supported, the interface allows you to answer/hang up a call in Bluetooth mode: Alpine, Clarion, Kenwood, Pioneer and ZENEC

General installation instructions:

Verification: 1: Check all operational functions and vehicle setting functions of the OEM HU. 2: Disconnect the OEM voltage-free HU. 3: Check all interface connections for correctness in voltage-free mode.

Connection and connection sequence: 1: Check the settings and hardware configuration of the dry contact interface. 2: Check the configuration of the radio connection cable without voltage. 3: Connect the radio connection cable according to the HU retrofit operating instructions. 4: Connect all other connections according to the HU retrofit operating instructions. 5: Connect the entire installation to the vehicle with the main connection last. 6: Configure the interface software according to the instructions in the section text and in the manual. 7: Configure the retrofit device according to the user manual of the retrofit device for steering wheel remote/camera/FSE/antenna phantom power and more. 8: Steering wheel remote and vehicle operation test

Changes in the configuration of the interface and cable for connecting the radio: 1: Change configuration without voltage 2: Reconnect, see above 5 to 8

If the interface or vehicle malfunctions: 1: Reinstall OEM HU 2: Support HU OEM 3: Determine CAN bus shutdown 4: Check the interface hardware configuration 5: Reconnecting after CAN bus shutdown, see above 5 and 6

More connections, connection changes, alternative connections, loose cable connections or extensions of loose cable connections mentioned in the information text or instructions are for guidance purposes only and are the information of a trained specialist installer.

More connections, changes to the wiring configuration in the wiring harness, or the use of alternative connections or connection extensions: 1: Connections and changes may only be made by trained installers. 2: Connections and modifications should be checked before connection for any manufacturer approvals or manufacturer warranty terms that the modifications may affect.